Effects of Synthesis Conditions on the Formation of Si-Substituted Alpha Tricalcium Phosphates

Powders of α-TCP containing various amounts of silicon were synthesized by two different methods: Wet chemical precipitation and solid-state synthesis. The obtained powders were then physico–chemically studied using different methods: Scanning and transmission electron microscopy (TEM and SEM), energy-dispersive X-ray spectroscopy (EDS), powder X-ray diffractometry (PXRD), infrared and Raman spectroscopies (FT-IR and R), and solid-state nuclear magnetic resonance (ssNMR). The study showed that the method of synthesis affects the morphology of the obtained particles, the homogeneity of crystalline phase and the efficiency of Si substitution. Solid-state synthesis leads to particles with a low tendency to agglomerate compared to the precipitation method. However, the powders obtained by the solid-state method are less homogeneous and contain a significant amount of other crystalline phase, silicocarnotite (up to 7.33%). Moreover, the microcrystals from this method are more disordered. This might be caused by more efficient substitution of silicate ions: The silicon content of the samples obtained by the solid-state method is almost equal to the nominal values.     

The effect of traffic data source on deterioration rates of heavy-duty flexible pavements

The purpose of this study is to assess the effect of traffic data source (estimated vs. actual) on predicted progression rates of roughness and rutting for heavy-duty flexible pavements of rural freeways. Progression rates are predicted using calibrated HDM-4 models. The assessment is performed in terms of variations in maintenance intervention timing associated with the variations in progression rates. Time series pavement condition data (covering 3–5 years) have been collected for 7 sections of rural freeways for use in calibrating HDM-4 deterioration models. They range in length from 10 to 60.8 km and cover different traffic volumes, climate zones and subgrade soil types. For these sections, estimated annual average daily traffic (AADT), growth factors and assumed loading have been extracted from relevant database. Only six segments of these sections have Weigh-in-Motion (WIM) sites so relevant actual AADT, growth factors and axle load distributions have been extracted from WIM reports. The results of running the calibrated HDM-4 deterioration models using different traffic data show that actual traffic data from WIM sites result in higher rates of deterioration to that of estimated data for four sites, resulting in earlier intervention timing and higher present value agency cost. The other two sites have lower rates with actual data due to lower traffic loading than estimated.     

On the thermal conductivity of bimodal SiC/A356 composites fabricated via powder metallurgy route

The present study investigates the thermal conductivity of bimodal SiC particulate distribution in aluminum matrix composites fabricated via powder metallurgy route. The effects of the SiC_p reinforcement size distribution and processing parameters such as sintering time and temperature on the thermal conductivity have been examined. The Box–Behnken experimental array was employed to identify the effects of selected variables on the thermal conductivity of the composite. A reasonable augmentation in the thermal conductivity was observed with an increase in sintering time and %volume fraction of fine SiC particulates. It has been demonstrated that the matrix doped with fine SiC particulates (37?µm) occupied interstitial positions and formed continuous SiC–matrix network resulting in minimizing the micropores that contributed for good thermal conductivity, that is, 235?W/mK. Scanning electron microscopy (SEM) and x-ray diffraction (XRD) were conducted to evaluate the microstructure architecture and interfacial phase formation.     

The control of paracetamol particle size and surface morphology through crystallisation in a spray dryer

The parameters governing the crystallisation of paracetamol using various conventional techniques has been extensively studied, however the factors influencing the drug crystallisation using spray drying is not as well understood. The aim of this work was to investigate the crystallisation of an active pharmaceutical ingredient through evaporative crystallisation using a spray dryer to study the physicochemical properties of the drug and to use semi-empirical equations to gain insight into the morphology and particle size of the dried powder. Paracetamol solutions were spray dried at various inlet temperatures ranging from 60 °C to 120 °C and also from a series of inlet feed solvent compositions ranging from 50/50% v/v ethanol/water to 100% ethanol and solid-state characterisation was done. The size and morphology of the dried materials were altered with a change in spray drying parameters, with an increase in inlet temperature leading to an increase in particle Sauter mean diameter (from 3.0 to 4.4 µm) and a decrease in the particle size with an increase in ethanol concentration in the feed (from 4.6 to 4.4 µm) as a result of changes in particle density and atomised droplet size. The morphology of the dried particles consisted of agglomerates of individual crystallites bound together into larger semi-spherical agglomerates with a higher tendency for particles having crystalline ridges to form at higher ethanol concentrations of the feed.     

Lewis acid-oxygen vacancy interfacial synergistic catalysis over SO42−/Ce0.84Zr0.16O2–WO3–ZrO2 for N,N-diethylation of aniline with ethanol

Herein, a new mechanism involving Lewis acid-oxygen vacancy interfacial synergistic catalysis for aniline N,N-diethylation with ethanol was proposed, and the SO₄²⁻/Ce_0.84Zr_0.16O₂–WO₃–ZrO₂ catalyst (SCWZ) with both Lewis acid sites and oxygen vacancies was synthesized by the hydrothermal method, which shows better catalytic activity than the reported solid acidic catalysts. Besides, the SO₄²⁻/ZrO₂ (SZ) and SO₄²⁻/WO₃–ZrO₂ (SWZ) catalysts were also prepared and compared with SCWZ to investigate the synergistic effect of each component. The SO₄²⁻ and WO₃ mainly generate Lewis acid by bonding with ZrO₂, which is beneficial for the fracture of the N–H bond in aniline. The Ce_0.84Zr_0.16O₂ solid solution mainly plays a vital role in generating the oxygen vacancies as the interface active species, which can participate in stripping –OH from ethanol, then the carbocation will also be released, which only needs 1.3805 kcal/mol energy, calculated by density functional theory (DFT), to be input. In comparison, the traditional reaction mechanism needs the Brønsted acidic sites to promote the protonation of ethanol, then dehydration and subsequent formation of carbocation followed, and 108.6846 kcal/mol energy needs to be input, which is far higher than that of the new mechanism. The apparent activation energy (E_a) over SCWZ was measured by experiment to be 34.09 kJ/mol, which is much lower than that of SWZ (47.10 kJ/mol) and SZ (54.37 kJ/mol), illustrating comparatively preferable kinetics for SCWZ than that of SWZ and SZ. Besides, the conversion of aniline and selectivity to N,N-diethylaniline over SCWZ reach almost 100% and 73%, respectively. The SCWZ can be renewed for 4 times without rapid deactivation, and the longevity of SCWZ is longer than that of SWZ and SZ, as the loaded SO₄²⁻ and tetragonal ZrO₂ are stabilized by Ce_0.84Zr_0.16O₂ and WO₃, respectively.     

夹杂物对工程机械用钢Q345FCA疲劳寿命的影响

采用QBWP-6000J型简支梁旋转弯曲疲劳试验机测定了高疲劳寿命工程机械用钢Q345FCA的疲劳寿命;采用扫描电镜(SEM)对疲劳断口形貌进行了观察,并用附带的能谱仪(EDS)寻找断口上的夹杂物;借助夹杂物自动分析系统对钢中的夹杂物进行了分析。通过对试验数据的分析,计算得出了Q345FCA钢和Q345钢夹杂物的表面临界尺寸、次表面临界尺寸和内部临界尺寸。结果表明,Q345FCA钢的疲劳极限为273 MPa,Q345钢的疲劳极限为266 MPa。Q345FCA钢和Q345钢中夹杂物尺寸均小于临界夹杂物尺寸,且断口形貌显示所有疲劳断裂均不是由夹杂物所引起,夹杂物不是疲劳源。     

紫金山东南矿段成矿期次、阶段浅析

通过对紫金山东南矿段铜钼(金)矿床地质矿化特征分析,指出铜钼矿化带主要赋存于花岗闪长斑岩的内外接触带,处于似斑状花岗闪长斑岩的上部,金矿化带赋存在表生氧化带的英安玢岩、隐爆角砾岩中。经过对矿石的组构特征、矿物生成顺序等特征分析,将矿床的成矿演化过程分为斑岩热液期、高硫化浅成低温热液期、表生氧化期三个主要矿化期次,进一步将斑岩热液期分为黑云母-钾长石化阶段、石英-绢云母化阶段、碳酸盐化阶段三个阶段;高硫化浅成低温热液期分为地开石化阶段、明矾石化阶段、硅化阶段三个阶段。研究结果为进一步研究矿床成因提供了依据。     

水平衡法与高温转化法在矿泉水氢氧稳定同位素测定中的应用

为了鉴别不同品牌矿泉水标注水源地信息真伪,对11种不同品牌饮用水的氢氧稳定同位素(δD和δ18 O)进行测定。结果表明,水平衡法(GasBench-IRMS)和高温转化法(TC/EA-IRMS)的测定结果一致性较好,两种方法测定6种不同饮用水的δD和δ18 O的平均差异分别为(0.6±1.59)‰和(0.02±0.13)‰。水平衡法需要较长的制备和测定时间,但δD和δ18 O的测定精度明显优于高温转化法。11种饮用水δD和δ18 O变化范围较大,其δD和δ18 O受不同品牌饮用水的水源地降水影响形成明显的地域性。虽然无法区分矿泉水是否由其他类别饮用水伪造,但δD和δ18 O可以为特定区域(如高海拔与沿海地区)以及产地相近的矿泉水水源地鉴别提供依据。